Sigma-Aldrich

Zinc oxide | Employed in the preparation of NaZnSiO3OH, a novel chiral framework material which has potential application in ion exchange, adsorption or catalysis | Buy chemicals and reagents online from Sigma Aldrich

Zinc oxide nanopowder, particle size 97 1314-13-2

nanopowder, &lt;50&#160;nm particle size (BET), &gt;97%

Zinc oxide nanopowder, &lt;50&#160;nm particle size (BET), &gt;97%

Zinc oxide

Effect of Microstructural Control on Thermoelectric Properties of Hot-Pressed Aluminum-Doped Zinc Oxide

Air-stable inverted flexible polymer solar cells using zinc oxide nanoparticles as an electron selective layer.

"Nanopowder synthesis of zinc oxide via solochemical processing.

Transparent Semiconducting ZnO:Al Thin Films Prepared by Spray Pyrolysis

Efficient hybrid solar cells from zinc oxide nanoparticles and a conjugated polymer.

The present study analyzed the effects of zinc oxide nanoparticles (ZnO-NPs) and zinc sulfate (ZnSO4) in the testis of six-month-old common carp Cyprinus carpio exposed to three different doses, viz., 10, 50, and 100 μg/L for 21 days. Characterization of ZnO-NPs was done after sonication, the size and shape of ZnO-NPs were determined as ∼20-30 nm spherical structure measured zeta potential of +26.0 mV. After treatment, determination of zinc (Zn) concentration in the testes revealed desired impact of the exposure. Expression of several transcription factors and few steroidogenic enzyme genes in the treated testis showed significant downregulation than the control. Measurement of oxidative stress-related enzymes such as catalase, superoxide dismutase, and glutathione-S-transferase revealed substantial elevation in the testis of treated groups when compared to control. Histological analysis of testis exhibited dose-related response, defective lumen, and slow progression of spermatogenesis. Exposure of both the forms of Zn on TM3 Leydig cell culture displayed loss of adhesion, clumping with decreased viability, and a significant increase in the apoptotic cells. In addition, comet and intracellular reactive oxygen species (ROS) assays authenticated DNA damage upon treatment with a significant increase in ROS. Histological analysis after treatment withdrawal showed revival of testis in carp to rescue the effect. Thus, the present report highlights the adverse effect of Zn on the testis function in common carp as well as evident drastically toxic in in vitro cultures.

Effects of zinc oxide nanoparticles and zinc sulfate on the testis of common carp, Cyprinus carpio.

Nanomaterials, including zinc oxide (ZnO) nanoparticles, are being developed for a variety of commercial products. Recent reports showed that cells exposed to ZnO nanoparticles produced severe cytotoxicity accompanied by oxidative stress and genotoxicity. To understand the possible mechanism underlying oxidative stress of ZnO nanoparticles, the present investigation focused on the direct bioactivity of ZnO nanoparticles using a rat retinal ganglion cell (RGC-5) culture. At concentrations relevant to those used in vitro exposure of RGC-5 cells to ZnO nanoparticles, it was found that ZnO nanoparticles could inhibit cell proliferation in time- and concentration-dependent manners. Meanwhile, cell cycle arrest of S and G2/M phases occurred in RGC-5 cells induced by ZnO nanoparticles. Moreover, our results also demonstrated that the overproduction of reactive oxygen species (ROS) and elevated level of caspase-12 as well as decreased levels of bcl-2 and caspase-9 occurred after treatment with different concentrations of ZnO nanoparticles when compared to those in untreated cells. In summary, our findings suggest that ZnO nanoparticles could lead to the over generations of ROS and caspase-12 as well as decreased levels of bcl-2 and caspase-9. These results indicate that bcl-2, caspase-9 and caspase-12 may play significant roles in ZnO nanoparticle-induced RGC-5 cell damage.

Zinc oxide nanoparticles induce rat retinal ganglion cell damage through bcl-2, caspase-9 and caspase-12 pathways.

Metal catalyst-free ZnO nanorods were grown on PS with buffer layers grown at 450 degrees C by plasma-assisted molecular beam epitaxy. Room temperature and temperature-dependent photoluminescence were carried out to investigate the optical properties of the ZnO nanorods with the average diameter of 120 nm and length of 300 nm. Three emission peaks, free excition, neutral-donor exciton, and free electron-to-neutral acceptor, were observed at 10 K. Huang-Rhys factor S of the ZnO nanorods was 0.978, which is much higher than that of ZnO thin films. The values of Varshni's empirical equation fitting parameters were alpha = 4 x 10(-3) eV/K, beta = 4.1 x 10(4) K, and E9(0) = 3.388 eV and the activation energy was about 96 meV.

Photoluminescence studies of ZnO nanorods grown by plasma-assisted molecular beam epitaxy.

ZnO-nanowire-based logic circuits were constructed by the vertical integration of multilayered field-effect transistors (FETs) on plastic substrates. ZnO nanowires with an average diameter of -100 nm were synthesized by thermal chemical vapor deposition for use as the channel material in FETs. The ZnO-based FETs exhibited a high I(ON)/I(OFF) of > 10(6), with the characteristic of n-type depletion modes. For vertically integrated logic circuits, three multilayer FETs were sequentially prepared. The stacked FETs were connected in series via electrodes, and C-PVPs were used for the layer-isolation material. The NOT and NAND gates exhibited large logic-swing values of -93%. These results demonstrate the feasibility of three dimensional flexible logic circuits.

Vertically integrated logic circuits constructed using ZnO-nanowire-based field-effect transistors on plastic substrates.

Organic solar cells are a favorable alternative to their inorganic counterparts because the functional layers of these devices can be processed with printing or coating on a large scale. In this study, a novel polymer was synthesized, blended with fullerene and deposited with inkjet printing for solar cell applications. Devices with printed layers were compared to those with spin coated films in order to evaluate inkjet printing as a thin film deposition method. Efficiency values of 3.7% were found for devices with inkjet printed or spin coated layers. Inkjet printing can be used to successfully process the active layers of organic solar cells consisting of novel polymers without sacrificing device performance.

Inkjet printed solar cell active layers based on a novel, amorphous polymer.

This paper reports the synthesis and characterization of ZnO nanoparticles prepared by soft chemical process. The nanoparticles of ZnO possess wurtzite hexagonal phase and were used for the induction of cell death in malignant human T98G gliomas, KB epithermoids and HEK normal non-malignant kidney cells. By applying ZnO nanoparticles, the cells exhibit that the nanoparticles are more efficacious on T98G cancer cells, moderately effective on KB cells and least toxic on normal human HEK cells. The results demonstrated that the treatment with ZnO nanoparticles sensitize T98G cells by increasing both the mitotic (linked to cytogenetic damage) and interphase (apoptosis) death. The ZnO nanoparticles behave as genotoxic drugs, since they induce a micronucleus formation in cells. The present study could be helpful in designing more potent anticancer agents for the therapeutic uses.

ZnO nanoparticles induces cell death in malignant human T98G gliomas, KB and non-malignant HEK cells.

Solution processed cathode organic photovoltaic cells (OPVs) utilizing thin layer of ZnO with 27% increase in power conversion efficiency (PCE) to control devices have been demonstrated. Devices without the presence of ZnO layer have much lower PCE than the ones with ZnO layer. Cathode modification layer can be used to reduce photogenerated excitions and finally improve the performance of the OPVs. The successful demonstrations of OPVs with an introduction of ZnO cathode layer give promise of further device progresses.

Organic photovoltaic solar cells with cathode modified by ZnO.

In this study, we present the synthesis of ZnO nanowire by hydrothermal process through reutilization of sludge from soy sauce wastewater electrochemical treatment. The influences of floc content and caramel pigment concentration on the morphologies of ZnO were studied. The products were characterized by XRD and SEM. The results showed that ZnO powder was of hexagonal wurtzite structure and well crystallized with high purity. Floc content and caramel pigment concentration played an important role in the final morphologies of ZnO nanowires. On the basis of these results, a possible growth mechanism for the formation of ZnO nanowires was described. These findings not only may contribute to control the synthesis of ZnO, but also present a novel method for the disposal of wastewater treatment sludge.

Preparation of ZnO nanowire using sludge from wastewater treatment.

The ZnO short nanorods and flowerlike nanostructures doped with Eu3+ ions are prepared by a hydrothermal method through adjusting the hydrothermal temperature. The XRD, FESEM, FT-IR, luminescent and photocatalytic properties are characterized. The results indicate that the hydrothermal temperature affects the morphology of ZnO:Eu3+ nanocrystals, short nanorods at 120 degrees C, flowerlike nanocrystals at 150 degrees C and nanoparticles at 180 degrees C. The structures of ZnO:Eu3+ nanocrystals prepared at different hydrothermal temperatures are assigned to hexagonal phase. The photoluminescent properties including excitation and emission spectra are studied. The charge transfer band and f-f transition absorption are observed in excitation spectra. And, the 5D(0)-7F(J) (J = 0-4) transition emissions appear in emission spectra. In addition, the photocatalytic properties are also studied. The degradation rate of ZnO:Eu3+ nanocrystals is a little lower than pure ZnO nanocrystals.

Preparation, photoluminescence and photocatalytic properties of ZnO:Eu3+ nanocrystals.

Here we report the fabrication and characteristics of graphene oxide (GO) field effect transistor gated with piezopotential of ZnO fine wires on a flexible substrate. The FET device consists of GO thin film on the bottom and ZnO piezoelectric fine wire (PFW) on the top. In the FET device the GO serves as a carrier transport channel and ZnO PFW acts as a gate. When the substrate is bent, a piezopotential is generated in the ZnO PFW. The piezopotential created by the strain in the ZnO PFW was used to control the carrier transport in the GO channel. This device demonstrates the application of piezoelectric ZnO PFW for creating the gating effect on the semiconducting performance of GO film.

ZnO piezoelectric fine wire gated graphene oxide field effect transistor.

Transparent conducting oxide (TCO) materials with high transmittance and good electrical conductivity have been attracted much attention due to the development of electronic display and devices such as organic light emitting diodes (OLEDs), and dye-sensitized solar cells (DSSCs). Aluminum doped zinc oxide thin films (AZO) have been well known for their use as TCO materials due to its stability, cost-effectiveness, good optical transmittance and electrical properties. Especially, AZO thin film, which have low resistivity of 2-4 x 10(-4) omega x cm which is similar to that of ITO films with wide band gap semiconductors. The AZO thin films were deposited on glass substrates by sol-gel spin-coating process. As a starting material, zinc acetate dihydrate (Zn(CH3COO)2 x 2H2O) and aluminum chloride hexahydrate (AlCl3 6H2O) were used. 2-methoxyethanol and monoethanolamine (MEA) were used as solvent and stabilizer, respectively. After deposited, the films were preheated at 300 degrees C on a hotplate and post-heated at 650 degrees C for 1.5 hrs in the furnace. We have studied the structural and optical properties as a function of Al concentration (0-2.5 mol.%).

Optical and structural properties of Al-doped ZnO thin films by sol gel process.

The influence of the encapsulation of In2O3 nanorods with ZnO on the H2S gas sensing properties was studied. In2O3-core/ZnO-shell nanorods were fabricated by a two step process comprising the thermal evaporation of an 1:1 mixture of In2O3 and graphite powders and the atomic layer deposition of ZnO. The core-shell nanorods ranged from 100 to 200 nm in diameter and were up to a few hundreds of micrometers in length. The thickness of the ZnO shell layer in the core-shell nanorod ranged from 5 to 10 nm. Multiple networked In2O3-core/ZnO-shell nanorod sensors showed the response of more or less 4 times higher than bare In2O3 nanorod sensors to H2S in a concentration range of 10-100 ppm at 300 degrees C. The substantial improvement in the response of In2O3 nanorods to H2S gas by the encapsulation with ZnO can be accounted for based on the space-charge model. Besides the enhanced sensor response, both the response and recovery times of the core-shell nanorods were shorter than those of the bare-In2O3 nanorods for any H2S concentration, respectively.

Enhanced gas sensing properties of multiple networked In2O3-core/ZnO-shell nanorod sensors.

The development of indium-free transparent conductive oxides (TCOs) on polymer substrates for flexible devices requires deposition at low temperatures and a limited thermal treatment. In this paper, we investigated the optical and electrical properties of ZnO/Cu/ZnO multi-layer electrodes obtained by ion beam sputtering at room temperature for flexible optoelectronic devices. This multilayer structure has the advantage of adjusting the layer thickness to favor antireflection and surface plasmon resonance of the metallic layer. We found that the optimal electrode is made up of a 10 nm-thick Cu layer between two 40 nm-thick ZnO layers, which results in a sheet resistance of 12 omega/(see symbol), a high transmittance of 85% in the visible range, and the highest figure of merit of 5.4 x 10(-3) (see symbol)/omega. A P3HT:PCBM-based solar cell showed a power conversion efficiency (PCE) of 2.26% using the optimized ZnO (40 nm)/Cu (10 nm)/ZnO (40 nm) anode.

Organic solar cells using a ZnO/Cu/ZnO anode deposited by ion beam sputtering at room temperature for flexible devices.

In this study, we fabricate planar pn heterojunction diodes composed of Cu2O nanoparticle (NP) films and single ZnO nanowires (NWs) on SiO2 (300 nm)/Si substrates and investigate their characteristics in the dark and under the illumination of white light and 325 nm wavelength light. The diode at bias voltages of +/- 1 V shows rectification ratios of 10 (in the dark) and 34 (under the illumination of white light). On the other hand, the diode exposed to the 325 nm wavelength light exhibits Ohmic characteristics which are associated with efficient photocurrent generation in both the Cu2O NP film and the single ZnO NW.

Characterization of planar pn heterojunction diodes constructed with Cu2O nanoparticle films and single ZnO nanowires.

This work reports the facile growth and characterizations of In-doped ZnO hollow spheres composed of nanosheets networks and nanocones. The In-doped ZnO hollow spheres composed of nanosheets networks and nanocones were grown on Si (100) substrate by simple and non-catalytic thermal evaporation process using metallic zinc and indium powders in the presence of oxygen. The prepared materials were examined in terms of their morphological, compositional, structural and optical properties. The detailed morphological studies revealed that the synthesized products are hollow spheres composed of nanosheet networks and nanocones and grown in high-density. The observed structural properties exhibited well-crystallinity and wurtzite hexagonal phase for the grown materials. The room-temperature photoluminescence (PL) spectrum showed a broad band in the visible region with a suppressed UV emission and hence due the enhancement in the green emission, the prepared materials exhibits a great interest in the area of ZnO phosphors, such as field emissive display technology, etc.

Growth of in-doped ZnO hollow spheres composed of nanosheets networks and nanocones: structural and optical properties.

One of the more traditional photovoltaic devices, single crystalline silicon solar cells were invented more than 50 years ago, currently make up 94% of the market. Single crystalline silicon solar cells operate on the principle of p-n junctions formed by joining p-type and n-type semiconductors.

Synthesis of ZnO Aggregates and Their Application in Dye-Sensitized Solar Cells

Dye-sensitized solar cells (DSCs) are 3rd generation solar cells combining the promise of high efficiency with low production costs.

Ruthenium-based dyes for Dye-sensitized Solar Cells

Organic photovoltaics (OPVs) represent a low-cost, lightweight, and scalable alternative to conventional solar cells. While significant progress has been made in the development of conventional bulk heterojunction cells, new approaches are required to achieve the performance and stability necessary to enable commercially successful OPVs.

Inverted Organic Photovoltaic Devices Using Zinc Oxide Nanocomposites as Electron Transporting Layer Materials

Among various ceramics, one-dimensional (1-D) piezoelectric ceramics have attracted significant scientific attention for use in energy harvesting.

Energy Harvesting Using Lead Zirconium Titanate-Based Ceramic Nanowires

While dye sensitization as the basis for color photography has been accepted for a very long time,1 attempts to use this principle for the conversion of solar light to electricity generally had resulted only in very low photocurrents, below 100 nA/cm

Understanding and Successfully Applying Materials for Dye-Sensitized Solar Cells

Electronically, it behaves as a wide band gap (3.2 eV) semiconductor and exhibits memristor properties.2 Optically, TiO2 has high opacity with a very high refractive index3 (>2.4), and it exhibits strong absorbance in the UV range.

Titania Nanotubes: Synthesis and Applications

The production of hydrogen by catalytic water splitting is important for a wide range of industries including renewable energy petroleum refining and for the production of methanol and ammonia in the chemical industry.

Molybdenum Disulfide: Understanding Hydrogen Evolution Catalysis

The past several decades have seen major advancements in the synthesis of metal nanomaterials. Most recently, controlled synthesis has become versatile enough to regulate the exact number of atoms and ligands of very small metal nanoparticles, referred to as “clusters”.

Zinc oxide

nanopowder, <50 nm particle size (BET), >97%

Properties

Quality Level

assay

form

contains

reaction suitability

particle size

surface area

SMILES string

InChI

InChI key

Description

Packaging

Application

Legal Information

Safety Information

Pictograms

Signal Word

Hazard Statements

Precautionary Statements

Hazard Classifications

Storage Class Code

WGK

Flash Point(F)

Flash Point(C)

Personal Protective Equipment

Documentation

Certificate of Analysis

Certificate of Origin

Brochures

More Documents

Quotes and Ordering

Peer Reviewed Papers

Protocols and Articles

Articles

Technical Service