KHGLS3THH1

Cápsula Durapore^® multicamadas 0,45/0,22 µm, Opticap^® XLT

Opticap^® XLT 30, cartridge nominal length 30 in. (75 cm), filter diam. 4.2 in. (10.7 cm)

• Código UNSPSC: 23151806

Propriedades

• Materiais: polyester support; polyethylene support; polypropylene filter; polypropylene housing; silicone seal
• Nível de qualidade: 400
• conformidade reg.: FDA 21CFR177-182 (all component materials)
• esterilidade: sterile; irradiated
• linha de produto: Opticap^® XLT 30
• Características: hydrophilic
• fabricante/nome comercial: Opticap^®
• Parâmetros: ≤45.0 mL/min air diffusion at 2.75 bar (40 psig) and 23 °C (in water); 1 bar max. inlet pressure (15 psi) at 80 °C; 1.05 bar max. differential pressure (15 psid) at 80 °C (Forward:); 2.75 bar max. inlet pressure (40 psi) at 60 °C; 25 °C max. inlet temp.; 3.5 bar max. differential pressure (50 psid) at 25 °C (Reverse; intermittent); 5.5 bar max. differential pressure (80 psid) at 25 °C (Forward:); 5.5 bar max. inlet pressure (80 psi) at 23 °C; 80 psig max. inlet pressure
• técnica(s): sterile filtration: suitable
• comprimento nominal do cartucho: 30 in. (75 cm)
• device L: 87.1 cm (34.3 in.)
• device size: 30 in.
• diâmetro do filtro: 4.2 in. (10.7 cm)
• filter filtration area: 0.1 m²
• diâm. conexão de entrada: 5/8 in.
• inlet to outlet width: 19.8 cm (7.8 in.)
• diam. conexão de saída: 5/8 in.
• Impurezas: ≤0.25 EU/mL bacterial endotoxins (LAL test, aqueous extraction); <0.25 EU/mL bacterial endotoxins (LAL test, sample aqueous extraction)
• matriz: Multilayer Durapore^®
• pore size: 0.45/0.22 μm pore size
• ponto de bolha: ≥3450 mbar (50 psig), air with water at 23 °C
• conector: 1/4 in. fitting (vent/drain hose barb with double O-ring seal); (16 mm (5?8 in.) Hose Barb Inlet and Outlet)

Descrição

Descrição geral

Device Configuration: Capsule

Embalagem

Double Easy-Open bag

Nota de preparo

Sterilization Method:
3 autoclave cycles of 60min at 126°C; not in-line steam sterilizable

This product was manufactured with a Durapore^® membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21CFR210.3(b)(6).

Nota de análise

Bacterial Retention: Samples were quantitatively retentive of a minimum Brevundimonas diminuta challenge concentration of 1 x 10⁷ CFU/cm² using ASTM^® F838 methodology.

TOC/Conductivity: After sterilization and a controlled water flush, samples exhibited less than 500ppb TOC per USP < 643 > and less than 1.3μS/cm per USP < 645 > at 25°C.

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥ 4.5 L

Outras notas

Directions for Use:

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer Wetting Instructions for Filter Units with Durapore^® Membrane user guide
• Storage Statement: Store in dry location
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations

Informações legais

ASTM is a registered trademark of American Society for Testing and Materials

Durapore is a registered trademark of Merck KGaA, Darmstadt, Germany

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany