KHGEG015HB3

Millipore Express^® SHC, Opticap^® XL Cápsula

inlet connection diam. 9/16 in., Opticap^® XL 150, pore size 0.5/0.2 μm, cartridge nominal length 3.8 in. (9.7 cm)

• Sinónimos: Opticap Gamma Compatible XL 150 Millipore Express SHC 0.5/0.2 μm 9/16 in. HB/HB with Bell
• UNSPSC Code: 23151806

Propiedades

• material: polyethersulfone ; polyethylene support; polypropylene (gamma-stable); polypropylene housing; polypropylene vent cap (Gamma stable); polysulfone ; silicone seal
• Quality Level: 400
• reg. compliance: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
• sterility: irradiated; non-sterile
• sterilization compatibility: gamma compatible
• product line: Opticap^® XL 150
• feature: gamma compatible; hydrophilic
• manufacturer/tradename: Millipore Express^®
• parameter: ≤1.0 mL/min air diffusion at 2.8 bar (40 psig) and 23 °C (in water); 1.0 bar max. differential pressure (15 psid) at 80 °C (Forward); 1.0 bar max. inlet pressure (15 psi) at 80 °C; 100 psi max. differential pressure (6.9 bar) (intermittent); 2.1 bar max. differential pressure (30 psid) at 25 °C (Reverse; intermittent); 2.75 bar max. inlet pressure (40 psi) at 60 °C; 25 °C max. inlet temp.; 5.5 bar max. differential pressure (80 psid) at 25 °C (Forward); 5.5 bar max. inlet pressure (80 psi) at 23 °C; 6.9 bar max. differential pressure (100 psid) at 25 °C (Forward; intermittent); 6.9 bar max. inlet pressure (100 psi) at 23 °C (intermittent); 80 psi max. differential pressure (5.5 bar) (continuous); 80 psig max. inlet pressure
• technique(s): sterile filtration: suitable
• L: 9.7 cm (3.8 in.)
• W: 2.2 in.
• cartridge nominal length: 3.8 in. (9.7 cm)
• diam.: 5.6 cm (2.2 in.)
• filtration area: 140 cm²
• inlet connection diam.: 9/16 in.
• inlet to outlet W: 9.7 cm (3.8 in.)
• outlet connection diam.: 9/16 in.
• impurities: ≤0.25 EU/mL bacterial endotoxins (LAL test, Aqueous extraction); <0.25 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
• matrix: Millipore Express^® SHC
• pore size: 0.5/0.2 μm pore size
• bubble point: ≥4000 mbar (58 psig), air with water at 23 °C
• fitting: 1/4 in. drain/vent hose barb (with double O-ring seal); inlet hose barb; outlet hose barb (with Bell); (14 mm (9/16 in.) Sanitary Flange Inlet and 14 mm (9/16 in.) Outlet with filling bell)

Descripción

General description

Device Configuration: Capsule

Packaging

Double Easy-Open bag

Other Notes

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.

Directions for Use

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer installation section of OPTICAP^® XL Capsules and OPTICAP^® XLT Capsules user guide
• Storage Statement: Store in dry location
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

Preparation Note

Sterilization Method
Gamma compatible to 45 kGy; 3 autoclave cycles of 60 min @ 123 °C; not in-line steam sterilizable

This product was manufactured with a Millipore Express^® membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).

Analysis Note

Bacterial Retention
Samples were quantitatively retentive of a minimum Brevundimonas diminuta challenge concentration of 1 x 10⁷ CFU/cm² using ASTM^® F838 methodology.

TOC/Conductivity
After sterilization and a controlled water flush of 1.0 L, samples exhibited less than 500 ppb TOC per USP <64> and less than 1.3 µS/cm per USP <64> at 25 °C.

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥1 L

Legal Information

ASTM is a registered trademark of American Society for Testing and Materials

MILLIPORE EXPRESS is a registered trademark of Merck KGaA, Darmstadt, Germany

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany

Disclaimer

EMD Millipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 97/23/EC of 29 May 1997. This product has been classified under Article 3 § 3 of the Pressure Vessel Directive. It has been designed and manufactured in accordance with sound engineering practice to ensure safe use. In compliance with Article 3 § 3 of this Pressure Vessel Directive, this product does not bear the CE mark.