Passa al contenuto
Merck
Tutte le immagini(1)

Key Documents

907669

Sigma-Aldrich

Silver ink

75 wt%, LIFT printable

Sinonimo/i:

Ag ink, Laser induced forward transfer

Autenticatiper visualizzare i prezzi riservati alla tua organizzazione & contrattuali
Tutte le immagini(1)

About This Item

Formula condensata:
Ag
Codice UNSPSC:
12352103
NACRES:
NA.23

Descrizione

Silver content : 75 wt%
Solvent : Diethylene Glycol Mono Butyl Ether (DGBE)
Surface Tension : 28 dyn/cm (Pendant Drop)

Forma fisica

paste

Dimensione particelle

50-70 nm (by Lumisizer™)
90-120 nm (by Lumisizer™)

Viscosità

50,000-100,000 cP (Shear Rate: 1 s-1
250cP - 450 cP (Shear Rate: 1000 s-1))

Densità

2.85-3.3

Temperatura di conservazione

15-25°C

Categorie correlate

Applicazioni

This Ag ink product is a conductive high viscous ink based on single-crystal silver nanoparticles in an organic solvent, has been designed for LIFT (Laser Induced Forward Transfer) digital printing and laser sintering.

The ink offers:
  • Uniform and reproducible donor layer with low drying speed
  • Stable accurate jetting in different types of laser systems, wide working window of jetting parameters
  • High speed printing (20-50kHz), allowing high throughput
  • Narrow patterning on plastic and glass substrates (line width ∼50 μm, height ∼0.5 μm, spacing ∼50 μm)
  • Laser sintering of LIFT printed pattern, providing good electrical properties


Fit for:
LIFT digital printing
Additive electronic manufacturing
Printed electronics: RFID, FPD, Sensors

Laser induced forward transfer printing (LIFT) is a non-contact, nozzle-free, one step, direct laser writing process.
LIFT can operate under atmospheric conditions, is compatible with low laser fluences, allows the printing of organic and inorganic materials as well as biological elements. The printing process can take place from both liquid and solid phases. It further has a high lateral resolution only defined by the laser spot size. It is a method compatible with inorganic semiconductor sensor fabrication, OLED fabrication and bio printing.

Altre note

Resistivity (4PP): After laser sintering* ≤ 8 μΩ·cm (≤ 5 bulk) for LIFT printed line (∼1-2 μm thick) on plastic substrate
*Parameters should be optimized depending on line geometry and substrate

Stoccaggio e stabilità

Keep container tightly closed. Store at room temperature, do not heat above 60 °C and do not freeze.

Note legali

Lumisizer is a trademark of LUM GmbH

Pittogrammi

Exclamation markEnvironment
GHS07,GHS09

Avvertenze

Warning

Indicazioni di pericolo

H319,H410

Classi di pericolo

Aquatic Acute 1 - Aquatic Chronic 1 - Eye Irrit. 2

Codice della classe di stoccaggio

10 - Combustible liquids

Classe di pericolosità dell'acqua (WGK)

WGK 3

Punto d’infiammabilità (°F)

Not applicable

Punto d’infiammabilità (°C)

Not applicable

Scegli una delle versioni più recenti:

Certificati d'analisi (COA)

Lot/Batch Number
MKCK2241

Non trovi la versione di tuo interesse?

Se hai bisogno di una versione specifica, puoi cercare il certificato tramite il numero di lotto.

Cerca un COA

Possiedi già questo prodotto?

I documenti relativi ai prodotti acquistati recentemente sono disponibili nell’Archivio dei documenti.

Visita l’Archivio dei documenti

I clienti hanno visto anche

Slide 1 of 1

1 of 1

Silver, dispersion nanoparticle, 30-35 wt. % in triethylene glycol monoethyl ether, spec. resistivity 11 μΩ-cm, for printing on plastic films

Sigma-Aldrich

736465

Silver, dispersion

Laser-induced forward transfer from healing silver paste films printing
Turkoz E, et al.
Applied Physics Letters, 113(22), 221601/1-221601/5 (2018)
Printing of complex free-standing microstructures via laser-induced forward transfer (LIFT) of pure metal thin films
Feinaeugle M, et al.
Additive Manufacturing, 24, 391-399 (2018)
V S Cheptsov et al.
Letters in applied microbiology, 67(6), 544-549 (2018-09-18)
Recently, it was shown that laser-induced forward transfer (LIFT) technology and the laser engineering of microbial systems (LEMS) technique (based on LIFT method) are effective for isolation of micro-organisms from different complex substrates. These techniques frequently utilize Au as an

Articoli

Advancements in the Fabrication of Integrated Organic Electronics

Professor Tokito and Professor Takeda share their new materials, device architecture design principles, and performance optimization protocols for printed and solution-processed, low-cost, highly flexible, organic electronic devices.

Il team dei nostri ricercatori vanta grande esperienza in tutte le aree della ricerca quali Life Science, scienza dei materiali, sintesi chimica, cromatografia, discipline analitiche, ecc..

Contatta l'Assistenza Tecnica.