KGW1A3TTT1

Polysep^™ II 1.0/0.2/0.1 µm nominal, Opticap^® XLT Capsule

inlet connection diam. 1.5 in., Opticap^® XLT 30, pore size 1.0/0.2/0.1 μm, cartridge nominal length 30 in. (75 cm)

• 别名: Opticap XLT30 Polysep II 1.0/0.2/0.1 μm 1-1/2 in. TC
• 分類程式碼代碼: 23151806
• eCl@ss: 32031610

属性

• 材料: borosilicate glass fiber (BGF) membrane; mixed cellulose esters (MCE) membrane; polypropylene ; polypropylene housing; polypropylene support; polypropylene vent cap; silicone seal
• 品質等級: 400
• 法律遵循: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
• 無菌: non-sterile
• 滅菌相容性: autoclavable compatible
• 產品線: Opticap^® XLT 30
• 特點: hydrophilic
• 製造商／商標名: Opticap^®
• 參數: 1.0 bar max. inlet pressure (15 psi) at 80 °C; 2.75 bar max. inlet pressure (40 psi) at 60 °C; 25 °C max. inlet temp.; 3.5 bar max. differential pressure (50 psid) at 25 °C; 5.5 bar max. inlet pressure (80 psi) at 23 °C; 80 psig max. inlet pressure
• 技術: prefiltration: suitable
• 長度: 87.1 cm (34.3 in.)
• 柱標稱長度: 30 in. (75 cm)
• 過濾面積: 1.26 m²
• 入口接頭直徑: 1.5 in.
• 入口到出口寬度: 15.2 cm (6.0 in.)
• 出口接頭直徑: 1.5 in.
• 雜質: ≤0.5 EU/mL bacterial endotoxins (LAL test, Aqueous extraction); <0.5 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
• 重量法萃取物: ≤435 mg/capsule
• 基質: Polysep^™ II
• pore size: 1.0/0.2/0.1 μm nominal pore size; 1.0/0.2/0.1 μm pore size
• 輸入: sample type liquid
• 接頭: inlet sanitary flange; outlet sanitary flange; (38 mm (1 1/2 in.) Sanitary Flange Inlet and Outlet)

说明

一般說明

Device Configuration: 取样皿滤膜

T-line/Gauge Port: T-line

特點和優勢

Format: Triple Layer

包裝

Double Easy-Open bag

其他說明

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.

Directions for Use:

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer to the first page of Visual Inspection Guide and introduction section of the Mixed cellulose esters Tech Brief
• Storage Statement: Please refer to the Mixed cellulose esters Tech Brief
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

準備報告

Sterilization Method
3 autoclave cycles of 30 min @ 121 °C; not in-line steam sterilizable

This product was manufactured with a media combination which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).

分析報告

Gravimetric Extractables: after a 15 L flush and 24 hours in water at controlled room temperature

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥15 L

法律資訊

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany

Polysep is a trademark of Sigma-Aldrich Co. LLC

安全信息

• 儲存類別代碼: 11 - Combustible Solids
• 水污染物質分類（WGK）: WGK 2