CGW374S03

Polysep^™II 1.0/0.2 µm 标称，小柱

pore size 1.0/0.2 μm, cartridge nominal length 40 in. (100 cm)

• 同義詞: Polysep II Cartridge Filter 40 in. 1.0/0.2 μm Code 7
• 分類程式碼代碼: 23151806
• eCl@ss: 32031610

屬性

• 材料: borosilicate glass fiber (BGF) membrane; mixed cellulose esters (MCE) membrane; polypropylene ; polypropylene support (Spun bonded); silicone seal
• 品質等級: 400
• 法律遵循: meets EU framework regulation [1935/2004/EC] (all component materials; regarding materials and articles intended to contact food); meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
• 無菌: non-sterile
• 滅菌相容性: autoclavable compatible; steam-in-place compatible
• 產品線: Polysep^™
• 特點: hydrophilic
• 製造商／商標名: Polysep^™
• 參數: 3.5 bar max. differential pressure (50 psid) at 25 °C; 3.5 bar max. inlet pressure (50 psi) at 25 °C
• 技術: prefiltration: suitable
• 長度: 40 in.
• 寬度: 2.7 in.
• 柱標稱長度: 40 in. (100 cm)
• 直徑: 7.1 cm (2.8 in.)
• 過濾面積: 1.84 m²
• 雜質: ≤0.5 EU/mL bacterial endotoxins (LAL test, Aqueous extraction); <0.5 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
• 重量法萃取物: ≤560 mg/cartridge
• 基質: Polysep^™ II
• pore size: 1.0/0.2 μm nominal pore size; 1.0/0.2 μm pore size
• 輸入: sample type liquid; sample type groundwater
• 柱代碼: Code 7

描述

一般說明

Device Configuration: Cartridge

特點和優勢

Format: Double Layer

包裝

Double Easy-Open bag

其他說明

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.

Directions for Use:

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer to the first page of Visual Inspection Guide and introduction section of the Mixed cellulose esters Tech Brief
• Storage Statement: Please refer to the Mixed cellulose esters Tech Brief
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

準備報告

Sanitization Protocol
30 min with hot water @ 80 °C

Sterilization Method
10 autoclave cycles or SIP @ 121 °C for 30 min

This product was manufactured with a media combination which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).

分析報告

Gravimetric Extractables: after 24 hours in water at controlled room temperature

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥20 L

法律資訊

Polysep is a trademark of Sigma-Aldrich Co. LLC

安全資訊

• 象形圖: GHS02
• 訊號詞: Danger
• 危險聲明: H228
• 防範說明: P210 - P240 - P241 - P280 - P370 + P378
• 危險分類: Flam. Sol. 1
• 儲存類別代碼: 4.1B - Flammable solid hazardous materials
• 水污染物質分類（WGK）: WGK 2