KHGEA1TTT1

Millipore Express^® SHC, Opticap^® XLT Capsule

inlet connection diam. 1.5 in., Opticap^® XLT 10, pore size 0.5/0.2 μm, cartridge nominal length 10 in. (25 cm)

• 동의어(들): Opticap Autoclavable XLT 10 Millipore Express SHC 0.5/0.2 μm 1-1/2 in. TC
• UNSPSC 코드: 23151806

속성

• material: polyethersulfone ; polypropylene ; polypropylene housing; polypropylene support; polypropylene vent cap; polysulfone ; silicone seal
• Quality Level: 400
• 규정 준수: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
• 무균: non-sterile
• 멸균 적합성: autoclavable compatible
• 제품 라인: Opticap^® XLT 10
• 특징: hydrophilic
• 제조업체/상표: Millipore Express^®
• 파라미터: ≤28.2 mL/min air diffusion at 2.8 bar (40 psig) and 23 °C (in water); 1.0 bar max. differential pressure (15 psid) at 80 °C (Forward); 1.0 bar max. inlet pressure (15 psi) at 80 °C; 100 psi max. differential pressure (6.9 bar) (intermittent); 2.1 bar max. differential pressure (30 psid) at 25 °C (Reverse; intermittent); 2.75 bar max. inlet pressure (40 psi) at 60 °C; 25 °C max. inlet temp.; 5.5 bar max. differential pressure (80 psid) at 25 °C (Forward); 5.5 bar max. inlet pressure (80 psi) at 23 °C; 6.9 bar max. differential pressure (100 psid) at 25 °C (Forward; intermittent); 6.9 bar max. inlet pressure (100 psi) at 25 °C (intermittent); 80 psi max. differential pressure (5.5 bar) (continuous); 80 psig max. inlet pressure
• 기술: sterile filtration: suitable
• 길이: 15.0 in.
• 너비: 4.2 in.
• 카트리지 공칭 길이: 10 in. (25 cm)
• 직경: 10.7 cm (4.2 in.)
• 여과 면적: 0.49 m²
• 입구 연결 직경: 1.5 in.
• 입구에서 출구 너비(W): 15.2 cm (6.0 in.)
• 출구 연결 직경: 1.5 in.
• 불순물: ≤0.25 EU/mL bacterial endotoxins (LAL test, Aqueous extraction); <0.25 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
• 기질: Millipore Express^® SHC
• pore size: 0.5/0.2 μm pore size
• 버블 포인트(bubble point): ≥4000 mbar (58 psig), air with water at 23 °C
• 피팅: 1/4 in. drain/vent hose barb (with double O-ring seal); inlet sanitary flange; outlet sanitary flange; (38 mm (1 1/2 in.) Sanitary Flange Inlet and Outlet)

설명

일반 설명

Device Configuration: Capsule

T-line/Gauge Port: T-line

포장

Double Easy-Open bag

기타 정보

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.

Directions for Use

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer installation section of OPTICAP^® XL Capsules and OPTICAP^® XLT Capsules user guide
• Storage Statement: Store in dry location
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

제조 메모

Sterilization Method
3 autoclave cycles of 60 min @ 126 °C; not in-line steam sterilizable

This product was manufactured with a Millipore Express^® membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).

분석 메모

Bacterial Retention
Samples were quantitatively retentive of a minimum Brevundimonas diminuta challenge concentration of 1 x 10⁷ CFU/cm² using ASTM^® F838 methodology.

TOC/Conductivity
After sterilization and a controlled water flush of 20 L, samples exhibited less than 500 ppb TOC per USP <64> and less than 1.3 µS/cm per USP <64> at 25 °C.

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥2 L

법적 정보

ASTM is a registered trademark of American Society for Testing and Materials

MILLIPORE EXPRESS is a registered trademark of Merck KGaA, Darmstadt, Germany

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany

면책조항

EMD Millipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 97/23/EC of 29 May 1997. This product has been classified under Article 3 § 3 of the Pressure Vessel Directive. It has been designed and manufactured in accordance with sound engineering practice to ensure safe use. In compliance with Article 3 § 3 of this Pressure Vessel Directive, this product does not bear the CE mark.