KPHLA02TH3

Durapore^® 0,45 µm, Opticap^® XL Cápsula

Opticap^® XL 2, inlet connection diam. 1.5 in., cartridge nominal length 2 in. (5 cm)

• Sinónimos: Opticap XL2 Durapore 0.45 μm without prefilter TC/HB
• Código UNSPSC: 23151806

Propiedades

• Materiales: PVDF ; polypropylene ; polypropylene housing; polypropylene support; polypropylene vent cap; silicone seal
• Nivel de calidad: 400
• cumplimiento norm.: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
• esterilidad: non-sterile
• Compatibilidad de esterilización: autoclavable compatible
• Línea del producto: Opticap^® XL 2
• Características: hydrophilic
• fabricante / nombre comercial: Opticap^®
• Parámetros: 1.0 bar max. inlet pressure (15 psi) at 80 °C; 2.8 bar max. inlet pressure (40 psi) at 60 °C; 25 °C max. inlet temp.; 3.4 bar max. differential pressure (50 psid) at 25 °C (Forward); 3.4 bar max. differential pressure (50 psid) at 25 °C (Reverse; intermittent); 5.5 bar max. inlet pressure (80 psi) at 23 °C; 80 psig max. inlet pressure
• técnicas: bioburden reduction: suitable
• Longitud: 14.2 cm (5.6 in.)
• Anchura: 3.3 in.
• longitud nominal del cartucho: 2 in. (5 cm)
• Diámetro: 8.4 cm (3.3 in.)
• filtración área: 0.09 m²
• diám. conexión a entrada: 1.5 in.
• An entrada a salida: 14.2 cm (5.6 in.)
• diám. conexión a salida: 9/16 in.
• impurezas: ≤0.5 EU/mL bacterial endotoxins (LAL test, Aqueous extraction); <0.5 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
• extraíbles gravimétricos: ≤10 mg/capsule
• matriz: Durapore^®
• tamaño de poro: 0.45 μm
• entrada: sample type liquid
• punto de burbuja: ≥1930 mbar (28 psig), air with water at 23 °C
• Adaptador: 1/4 in. drain/vent hose barb (with double O-ring Seal); inlet sanitary flange; outlet hose barb; (38 mm (1 1/2 in.) Sanitary Flange Inlet and 14 mm (9/16 in.) Hose Barb Outlet)

Descripción

Descripción general

Device Configuration: Capsule

Envase

Double Easy-Open bag

Otras notas

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.

Directions for Use

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer Wetting Instructions for Filter Units with Durapore^® Membrane user guide
• Storage Statement: Store in dry location
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

Nota de preparación

Sterilization Method
3 autoclave cycles of 60 min @ 126 °C; not in-line steam sterilizable

This product was manufactured with a Durapore^® membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).

Nota de análisis

Gravimetric Extractables: after 24 hours in water at controlled room temperature

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥500 mL

Información legal

Durapore is a registered trademark of Merck KGaA, Darmstadt, Germany

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany

Cláusula de descargo de responsabilidad

EMD Millipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 97/23/EC of 29 May 1997. This product has been classified under Article 3 § 3 of the Pressure Vessel Directive. It has been designed and manufactured in accordance with sound engineering practice to ensure safe use. In compliance with Article 3 § 3 of this Pressure Vessel Directive, this product does not bear the CE mark.