KHVES003HH3

Millipore Express^® SHRP, Opticap^® XL Capsule

sterile, Opticap^® XL 3, inlet connection diam. 9/16 in., pore size 0.5/0.1 μm, cartridge nominal length 4.7 in. (11.9 cm)

• Sinónimos: Opticap Sterile XL 300 Millipore Express SHR with Prefilter 0.5/0.1 μm 9/16 in. HB/HB
• Código UNSPSC: 23151806
• eCl@ss: 32031690

Propiedades

• Materiales: polyethersulfone membrane; polyethylene support; polypropylene (gamma-stable); polypropylene housing; polypropylene vent cap (Gamma stable); polysulfone ; silicone seal
• Nivel de calidad: 400
• cumplimiento norm.: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
• esterilidad: irradiated; sterile
• Línea del producto: Opticap^® XL 3
• Características: hydrophilic
• fabricante / nombre comercial: Millipore Express^®
• Parámetros: ≤1.9 mL/min air diffusion at 3.45 bar (50 psig) and 23 °C ( in water); 1.0 bar max. differential pressure (15 psid) at 80 °C (Forward); 1.0 bar max. inlet pressure (15 psi) at 80 °C; 100 psi max. differential pressure (6.9 bar) (intermittent); 2.1 bar max. differential pressure (30 psid) at 25 °C (Reverse; intermittent); 2.75 bar max. inlet pressure (40 psi) at 60 °C; 25 °C max. inlet temp.; 5.5 bar max. differential pressure (80 psid) at 25 °C (Forward); 5.5 bar max. inlet pressure (80 psi) at 25 °C; 6.9 bar max. differential pressure (100 psid) at 25 °C (Forward; intermittent); 6.9 bar max. inlet pressure (100 psi) at 25 °C (intermittent); 80 psi max. differential pressure (5.5 bar) (continuous); 80 psig max. inlet pressure
• técnicas: sterile filtration: suitable
• Longitud: 11.9 cm (4.7 in.)
• longitud nominal del cartucho: 4.7 in. (11.9 cm)
• Diámetro: 10.9 cm (4.3 in.)
• filtración área: 300 cm²
• diám. conexión a entrada: 9/16 in.
• An entrada a salida: 11.9 cm (4.7 in.)
• diám. conexión a salida: 9/16 in.
• impurezas: ≤0.25 EU/mL (LAL test, Aqueous extraction); <0.25 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
• matriz: Millipore Express^® SHR (w/Prefilter)
• pore size: 0.5/0.1 μm pore size
• punto de burbuja: ≥2586 mbar (37.5 psig), nitrogen with 70/30% IPA/water at 23 °C
• Adaptador: 1/4 in. drain/vent hose barb (with double O-ring seal); inlet hose barb; outlet hose barb; (14 mm (9/16 in.) Hose Barb Inlet and Outlet)

Descripción

Descripción general

Device Configuration: Capsule

Envase

Double Easy-Open bag

Otras notas

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.

Directions for Use

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer installation section of OPTICAP^® XL Capsules and OPTICAP^® XLT Capsules user guide
• Storage Statement: Store in dry location
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

Nota de preparación

Sterilization Method
3 autoclave cycles of 60 min @ 123 °C; not in-line steam sterilizable

This product was manufactured with a Millipore Express membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).

Nota de análisis

Bacterial Retention
Samples were quantitatively retentive of a minimum Brevundimonas diminuta challenge concentration of 1 x 10⁷ CFU/cm² using ASTM^® F838 methodology.

TOC/Conductivity
After sterilization and a controlled water flush of 2.0 L, samples exhibited less than 500 ppb TOC per USP <64> and less than 1.3 µS/cm per USP <64> at 25 °C.

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥1 L

Información legal

ASTM is a registered trademark of American Society for Testing and Materials

MILLIPORE EXPRESS is a registered trademark of Merck KGaA, Darmstadt, Germany

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany

Cláusula de descargo de responsabilidad

EMD Millipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 97/23/EC of 29 May 1997. This product has been classified under Article 3 § 3 of the Pressure Vessel Directive. It has been designed and manufactured in accordance with sound engineering practice to ensure safe use. In compliance with Article 3 § 3 of this Pressure Vessel Directive, this product does not bear the CE mark.