KPGES015FH3

Millipore Express^® PHF, Opticap^® XL Capsule

Opticap^® XL 150, sterile, inlet connection diam. 3/4 in., cartridge nominal length 3.8 in. (9.7 cm)

• 동의어(들): Opticap XL 150 Millipore Express PHF Sterile 0.2 μm 3/4 in. TC-9/16 in. HB
• UNSPSC 코드: 23151806

속성

• material: polyethersulfone ; polyethylene support; polypropylene (gamma-stable); polypropylene housing; polypropylene vent cap; polysulfone ; silicone seal
• Quality Level: 400
• 규정 준수: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
• 무균: irradiated; sterile
• 제품 라인: Opticap^® XL 150
• 특징: hydrophilic
• 제조업체/상표: Millipore Express^®
• 파라미터: ≤1.4 mL/min air diffusion at 2.8 bar (40 psig) and 23 °C (in water); 1.0 bar max. inlet pressure (15 psi) at 80 °C; 1000 bar max. differential pressure (15 psi) at 80 °C; 2.75 bar max. inlet pressure (40 psi) at 60 °C; 25 °C max. inlet temp.; 5.5 bar max. inlet pressure (80 psi) at 25 °C; 5500 mbar max. differential pressure (80 psi) at 25 °C; 80 psig max. inlet pressure
• 기술: bioburden reduction: suitable
• 길이: 9.7 cm (3.8 in.)
• 카트리지 공칭 길이: 3.8 in. (9.7 cm)
• 직경: 5.6 cm (2.2 in.)
• 여과 면적: 220 cm²
• 입구 연결 직경: 3/4 in.
• 입구에서 출구 너비(W): 9.7 cm (3.8 in.)
• 출구 연결 직경: 9/16 in.
• 불순물: ≤0.25 EU/mL bacterial endotoxins (LAL test, Aqueous extraction); <0.25 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
• 기질: Millipore Express^® PHF
• 공극 크기: 0.2 μm
• 피팅: 1/4 in. drain/vent hose barb (with double O-ring seal); inlet sanitary flange; outlet hose barb; (19 mm (3/4 in.) Sanitary Flange Inlet and 14 mm (9/16 in.) Hose Barb Outlet)

설명

일반 설명

Device Configuration: Capsule

Sterile capsules meet current USP and AAMI guidelines for sterility utilizing a validated sterilization cycle.

포장

Double Easy-Open bag

기타 정보

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.

Directions for Use

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer wetting instructions of Filters with MILLIPORE EXPRESS^® Membrane user guide
• Storage Statement: Please refer Filters with MILLIPORE EXPRESS^® Membrane user guide
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

제조 메모

Sterilization Method
3 autoclave cycles of 60 min @ 123 °C; not in-line steam sterilizable

This product was manufactured with a Millipore Express^® membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).

분석 메모

Bacterial Retention
Samples of membrane used in this filter were quantitatively retentive of a minimum Brevundimonas diminuta challenge concentration of 1 x 10⁷ CFU/cm² using ASTM^® F838 methodology.

TOC/Conductivity
After sterilization and a controlled water flush of 2.0 L, samples exhibited less than 500 ppb TOC per USP <64> and less than 1.3 µS/cm per USP <64> at 25 °C.

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥1 L

법적 정보

ASTM is a registered trademark of American Society for Testing and Materials

MILLIPORE EXPRESS is a registered trademark of Merck KGaA, Darmstadt, Germany

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany

면책조항

EMD Millipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 97/23/EC of 29 May 1997. This product has been classified under Article 3 § 3 of the Pressure Vessel Directive. It has been designed and manufactured in accordance with sound engineering practice to ensure safe use. In compliance with Article 3 § 3 of this Pressure Vessel Directive, this product does not bear the CE mark.