Skip to Content
Merck
HomeMammalian Cell CultureCell Dissociation Protocol using Trypsin

Cell Dissociation Protocol using Trypsin

Various proteolytic enzymes are used to detach cells from the adherent substrate, of which the trypsin a member of serine protease family is most frequently used. Trypsin is produced from proenzyme, trypsinogen secreted by exocrine cells of pancreas; Trypsin acts on C-terminal side of Lysine or Arginine. Optimum activity is achieved at 37 °C, so pre-warmed trypsin speed up the detachment. Long term incubation with high trypsin concentration damage cells by striping cell surface proteins and kill the cells.

Trypsin is tolerated by many cell types; however it is desirable to avoid trypsin in proteomic studies and serum-free cultures. Based on the application and cell types trypsin is employed with various constituents and concentration. Some of the attributes are discussed below.

  • EDTA (disodium ethylenediaminetetraacetic acid): Adhesion molecules in the presence of calcium determine cell-cell and cell-matrix interaction. To weaken the interactions, EDTA is frequently included with Trypsin which chelates the divalent cations (Ca2+, Mg 2+).
  • Phenol red: Optimum activity of trypsin is achieved at pH range from 7 to 9 (5466615). At this range inclusion of phenol red gives pink color. Due to environmental conditions the pH of trypsin may turn acidic, giving orange color and renders trypsin less effective. By adjusting the pH to 7.4 – 7.6 with NaOH trypsin activity could be optimized.
  • Diluent: Concentrated trypsin is being solubilized or diluted in a buffered salt solution that contains no Ca2+ or Mg2+, such as Hank's Balanced Salt Solution (Product No. H9394), which maintains pH and osmotic balance. Besides, some trypsin products have 0.9% NaCL as diluent instead of hanks balanced salt solution.
  • Source and form: The major source of trypsin is porcine, which is available either in the form of lyophilized powder or as in solution. To avoid animal or microbial products, recombinant bovine trypsin is also expressed in corn, called Trypzean solution (T3449).
  • Concentration: Based on the cell type and application trypsin is used in various concentrations. For strongly adherent cell lines, trypsin of 2.5 % to 0.25% (10X to 1X power) is used. While the studies which require cell surface protein integrity, lower concentrated (0.05% trypsin) solutions are employed.

Protocol

  1. Pre-warm the trypsin solution, balanced salt solution (Ca+2 and Mg+2-free solution) and growth medium to 37 °C
  2. Examine the cells to ensure the cells are healthy and free of contamination
  3. Remove and discard the culture media from flask
  4. Gently rinse the cells with balanced salt solution without Ca+2 and Mg+2 ions and remove the solution. Firmly adherent cells could also be washed with tryspin solution. However, for sensitive cells balanced salt solution is preferred.
  5. Add appropriate quantity (0.5 mL/10 cm2) of pre-warmed trypsin solution to the side wall of the flask. Gently swirl the contents to cover the cell layer.
  6. Incubate the vessel in room temperate for 2-3 minutes. Firmly adherent cells can be detached quickly at 37 °C. Observe the cells under microscope. The detached cells appear rounded and refractile under microscope. If less than 90% of cells are detached incubate the flask for another 2 minutes and observe the cells under microscope for every 30 seconds.
    Note: Prevent cell exposure to trypsin solution for longer periods (>=10 min)
  7. Once cells appear detached add two volumes of pre-warmed complete growth media to inactivate trypsin. Gently disperse the medium by pippeting over the cell layer surface several times to ensure recovery of >95% of cells. For serum free cultures, Soybean trypsin inhibitor (Product No. T6414) is added at an equimolar concentration to inhibit the trypsin.
    Note: Vigorous pipetting cause cell damage.
  8. Transfer the cell suspension to the tube and gently centrifuge at 300-1000 X g for 5-10 min. After removing the supernatant, gently resuspend the cell pellet in pre-warmed complete growth medium. Remove required sample to determine the cell density of viable cells by using hemocytometer and trypan blue exclusion or automated cell counter.
  9. Dilute the remaining solution to the seeding density and pipet appropriate volume to the culture flask and place it in the incubator.
Flask Area Media Volume
25 cm25 – 10 mL
75 cm210 – 30 mL
175 cm240 – 150 mL
Cell dissociation with Tripsin protocol

Figure 1.

Troubleshooting: Cell Detachment

IssuesReasonsSolutions
Cells difficult to detach from culture flasks
  • Loss of enzyme activity (trypsin) or low concentration
  • Presence of serum (inhibits trypsin activity)
  • High confluence and enzyme could not access cell-substrate interface
  • Use fresh lot of enzyme with optimum concentration
  • Thorough rinse to remove serum
  • Cell detachment at lower cell density
Difficulty in cell adherence
  • Use of high concentrations of trypsin
  • Trypsin not inactivated fully
  • Insufficient attachment factors and serum
  • Contamination
  • Citrate reduce the availability of calcium and results in reduced cell attachment
  • Cell membrane damage
  • Trypsinize with optimum concentration for less time
  • Add serum to inactivate trypsin
  • Use antibiotics to salvage the culture  and if the contamination is not cleared after 14 days discard the infected cell lot
  • Eliminate and reduce the level of citrate used in cell culture systems
  • Avoid prolonged exposure to trypsin. Store media and culture system away from fluorescent light to reduce toxic effects of free radicals
Cells detaching and low viability
  • Contamination
  • Lack of sufficient attachment factors and serum
  • High confluent cells
  • Oxidative stress cause rounding up and detaching cells from their substrates
  • Change in osmolality (pH) in trypsin solution
  • Discard contaminated cells
  • Add appropriate attachment factors and serum
  • Split and passage the cells
  • Minimize oxidative stress by adding albumin, glutathione
  • Verify pH of trypsin solution
Cells clump after detachment
  • Use of high concentration of trypsin
  • Vigorous pipetting
  • Vigorous and long centrifugation
  • Increased age of monolayers
  • Trypsinize with optimum concentration
  • Gentle pipetting
  • Gentle centrifugation (10 minutes at 125 X g)
  • Split and passage the cells before it reaches 100% confluence
Cell membrane damage and cell death
  • Increase in lipid peroxidation that degrade cell membranes causing cells to detach
  • Lack of ceruloplasmin in serum-free media catalyze the formation of hydroxyl free radicals and damage cell membrane
  • Increased iron concentration in solution support free radical activity at the cell surface and damage the cell membrane
  • Hydrogen peroxide form hydroxyl free radicals in presence of ferrous and cuprous ions
  • Light breakdown riboflavin and forms hydrogen peroxide
  • Loss of zinc due to precipitation in presence of oxide, peroxide, carbonate, hydroxyl, phosphate and sulfide anions.
  • Add ascorbate and glutathione to arrest lipid peroxidation
  • Include albumin and glutathione in the formulation to reduce the oxidative damage
  • Use transferring to sequester iron for delivery to cells
  • Include mannitol/pyruvate in medium to complex and stabilize hydrogen peroxide.
  • Add fresh riboflavin to the cell culture and avoid prolong exposure of cell culture system to light
  • Add zinc as a complex with albumin/insulin and minimize the oxidative stress to prevent formation of oxides, peroxides and sulfides

For more information, including various other applications and protocols of Trypsin, please click here.

Materials
Loading
Sign In To Continue

To continue reading please sign in or create an account.

Don't Have An Account?